EMS for 50 kW / 100 kWh Battery CabinetsA small site's first battery, run to earn and to protect.

A 50 kW / 100 kWh cabinet is the entry size for commercial battery storage: a shop, office, cold store or small factory. The EMS decides whether it trims the peak, shifts to off-peak hours or waits for an outage.

Commercial & industrial

50 kW / 100 kWh

Power
50 kW
Energy
100 kWh
At full power
about 2 hours
Format
Outdoor all-in-one battery cabinet
Ingro EMS-CIIngro EMS-EVAny battery, BMS or PCS
The short answer

For a 50 kW / 100 kWh battery cabinet, the EMS is the controller that decides when the battery charges and discharges against your tariff, your demand limit and your solar. Ingro EMS-CI runs a cabinet this size to trim up to 50 kW off the peak for about two hours, move energy from peak to off-peak hours, keep a backup reserve and store rooftop solar, with any maker's cabinet, BMS and PCS.

Ingro does not make the battery. The cabinet or container can be any maker's, with any BMS and PCS; Ingro EMS is the controller and software that decides when it charges, discharges or holds.

The battery

What a 50 kW / 100 kWh BESS Usually Is

What a battery of this size usually looks like on an Indian site.

  • One outdoor cabinet, usually with the battery, BMS, PCS, cooling and fire protection inside (an all-in-one unit).
  • Typically LFP cells, about 100 kWh, with a 50 kW PCS — around two hours at full power.
  • Connected at the site's LT panel, often next to rooftop solar and a diesel generator.
Where it works

Where a 50 kW / 100 kWh Battery Earns Its Keep

The sites that most often install a 50 kW / 100 kWh battery.

Shops, offices and showrooms

Cut the demand charge and the peak-hour bill; keep lights, IT and lifts on in an outage.

Cold stores and small factories

Ride through cuts without starting the DG for every short outage.

Petrol pumps and small EV charging

Carry a charger's peak on a small grid connection.

Want an engineer to call you?

Leave your details. An Ingro engineer gets back to you within one business day, no obligation.

Or tell us about your site ↓
What Ingro EMS does

Ingro EMS on a 50 kW / 100 kWh Battery

The battery stores energy and the PCS converts it. The EMS decides what it earns, every control cycle.

Peak shaving

Does the battery hold the demand limit?

The EMS watches the main meter and discharges only when demand would cross the limit you set, so the monthly demand charge stays down.

ToD shifting

Is it charged when power is cheap?

Charge in off-peak or solar hours, discharge in the peak tariff window, with a reserve kept back for outages.

Backup

What happens in a power cut?

The reserve carries the critical loads; the DG starts only if the outage outlasts it.

Solar

Where does the midday solar go?

Excess rooftop solar is stored instead of exported or curtailed, and used in the evening.

Connecting it

Which Ingro EMS Runs This Size

Most cabinets this size have the PCS and BMS inside and expose them over Modbus TCP or Modbus RTU (RS485). Ingro EMS reads both, plus the main meter, the solar inverters and the DG controller. It speaks Modbus TCP, Modbus RTU over RS485, SunSpec, IEC 61850, DNP3 and OPC-UA, plus dry contacts, digital I/O and aggregator gateways. Ingro EMS is deployed on site (offline), in the cloud, or as a hybrid of the two. In on-site and hybrid deployments, site control continues with no internet connection.

Building batteries of this size? Ingro EMS for integrators, EPCs and pack makers · Every BMS, PCS and protocol

Common questions

EMS for a 50 kW / 100 kWh BESS, Answered

4 questions

One that reads the battery, the PCS and the site's main meter, and runs peak shaving, ToD shifting, backup and solar storage together. Ingro EMS-CI does this with any maker's cabinet.

Yes. Ingro EMS runs several cabinets as one battery, so a second or third cabinet is added without changing the controller.

The built-in controller protects the battery and runs simple timers. It does not see the main meter, the tariff, the solar or the DG, so it cannot hold a demand limit or decide between backup and savings. That is the EMS's job.

Send the battery size and make, the PCS, a year of electricity bills or the load profile, and what the battery must do (peak shaving, backup, solar, DG, dispatch). An engineer replies within one business day with a scope of supply.

Still have a question?

Share details of your site, hardware and tariff or tender, and an engineer will answer it.

Every size

Ingro EMS for Every Battery Size

One controller and one console, from a home battery to a grid-scale plant.

Compare all sizes

Running a 50 kW / 100 kWh Battery? Put Ingro EMS on It.

Send the battery and what it must do. An engineer replies within one business day.

You send
  • 1The battery size and make, and the PCS
  • 2A year of bills or the load profile
  • 3What the battery must do: peak, backup, solar, DG or dispatch
We return
  • An EMS scope of supply
  • Which Ingro EMS package fits, and how it connects
  • Or a complete BESS proposal, if you hand over the plant

Get a Proposal for Your 50 kW / 100 kWh Battery

Tell us the battery, the PCS and what it must do. An engineer replies within one business day with the EMS scope and the package that fits.

What are you looking for?

An engineer replies within one business day. Bills, drawings or data files can go in reply to that email, or to contact@ingroenergy.com. Privacy policy